Sanitary 1,000L Ribbon Blender Retrofit for a Rapid-Changeover Color Masterbatch Producer

Standalone Process Improvement
Masterbatch Manufacturers
Color Masterbatch
Resin
Pellets
Powder
Cross-contamination between materials
Long changeover and cleaning time
Uneven additive distribution

Etapa verificada: In Operation
Fecha del proyecto: 2024-02
Aplicación principal: Color & Additive Masterbatch Compounding and Rapid-Changeover Line
Identidad del cliente: Anonymized
Ubicación del proyecto: South China Chemical & Polymer Park

Placeholder image: project photo, set as the featured image, 1600 × 900 px (16:9). It shows the space reserved for approved material and is not a photograph of our equipment. — **Placeholder · 1600 × 900 px (16:9)（占位图）** Replace with an approved project photo, set as the featured image at this size.（按此尺寸替换为正式图片。）

The situation

Where this project started

Objetivo del cliente

Reduce manual color-change cleaning time between contrasting color batches to under 20 minutes, eliminate resin cross-contamination spots, and achieve superior pigment de-agglomeration resulting in blown film FPV < 1.0 bar/g.

Perfil del cliente

An export-oriented color masterbatch and functional additive producer in South China operating four twin-screw compounding lines with an annual capacity of 12,000 tons of high-opacity blown-film masterbatches.

Antecedentes del proyecto

In custom color masterbatch manufacturing, rapid customer order turnaround and small lot sizes require agile recipe changeovers. Inefficient mixer cleanouts waste hundreds of productive extrusion hours annually and create severe risk of off-color carbon speck or pigment contamination in film extrusion.

Condiciones iniciales

The facility previously utilized conventional vertical high-speed hot mixers for pre-blending pigments and PE/PP wax. High tip speeds generated frictional heat that softened carrier waxes, causing pigments to cake onto the vessel walls and beneath bottom agitator blades. Cleanout required two operators using copper scrapers, solvent rags, and vacuum hoses for up to two hours per color change.

Limitaciones clave

The blender had to be cleaned dry without water washing, as residual liquid would destroy the moisture tolerance of downstream polyolefin film masterbatches.

Delivery

What was delivered, and why it was chosen

Por qué esta selección

A Horizontal Ribbon Blender was chosen over high-speed vertical mixers because its gentle, convective folding action prevents carrier wax from softening and sticking to the walls, enabling rapid dry cleaning without solvent wiping or baking.

Personalización específica del proyecto

Configured with sanitary mirror-polish (Ra ≤ 0.4 µm) on both trough walls and ribbon blades, complemented by a segmented quick-disassembly packing gland seal to allow 5-minute seal packing inspection without dismounting bearings.

Alcance entregado

Equipment Sanitary 1,000L Horizontal Ribbon Blender HRM-1000: Effective capacity 1,000 L, mirror-polished SUS304 (Ra ≤ 0.4 µm), double helical counter-flow ribbon, 15 kW drive

Core gentle pre-blending unit fluidizing virgin polymer granules, pigment powders, and wax dispersants without frictional melting.

Equipped with split air-purged labyrinth shaft seals and full-opening gas-spring inspection cover.

1 set
Accessory Full-Length Pneumatic Contour Discharge Gate Curved radius flush flap matching cylinder curvature with silicone seal and pneumatic dual-cylinder actuator

Eliminates dead pockets beneath the blender trough and discharges 99.8% of batch in under 25 seconds.

Interlocked with safety limit switches and dust-tight transition sleeve.

1 set
System High-Pressure Air-Pulse Internal Cleanout System Integrated manifold with 8 rotating air-pulse nozzles powered by 0.7 MPa shop air

Blows down residual pigment dust from ribbon arms and vessel walls directly into the discharge chute.

Pre-programmed automated 90-second dry blowout cycle on operator panel.

1 set
Service Engineering Commissioning & Operator Training Service 3 days on-site installation supervision, dry-swab cleaning validation, and standard operating procedure (SOP) delivery

Setup, color-change validation, and operator certification.

Delivery included cleanout validation swab kit.

1 service

Verification

How far the project is verified

Factory Tested

Internal ribbon-to-trough radial clearance verified across all flights at 3.0 mm ± 0.5 mm; dynamic ribbon balance confirmed with zero trough vibration; air-purged seals pressure tested at 0.3 MPa air supply.
Shipped

Shipped fully assembled in an export wooden crate with moisture-resistant barrier film packaging.
Installed

Positioned on an elevated mezzanine directly feeding the feed hopper of twin-screw extrusion line #2. Rigging and electrical connections were completed in two days during weekend maintenance.
Commissioned

Commissioned across five contrasting color changeovers: black -> white, green -> translucent red, and yellow -> natural base. Cleanout protocols were timed with an industrial stopwatch, and pigment residue swabbing tests confirmed zero cross-color contamination.
In Operation Verified

In continuous operation for over 10 months across two shifts. Operators execute an average of 4 to 6 color recipe transitions per day using the automated air-sweep and quick-wipe protocol.

Results

What changed, and what backs it

Contrasting Color Changeover Cleaning Duration

95 14

minutes

Complete cleanout time between highly contrasting color batches was slashed from 95 minutes down to 14 minutes, recovering 16.5 hours of productive extrusion time per week.

Evidencia Commissioning Record

Duración de la prueba: 5 consecutive color change trials
Fecha de la evidencia: 2024-02
Condiciones reales de entrada y salida: Full color transition from phthalocyanine dark green to pure natural virgin LDPE resin.
Método de medición: Timed stopwatch duration from blender stop to cleanout sign-off ready for subsequent batch charging.

Filter Pressure Value (FPV) on Blown Film Grade

2.85 0.78

bar/g

Downstream masterbatch Filter Pressure Value (FPV) plummeted from 2.85 bar/g to 0.78 bar/g, completely eliminating pigment agglomeration gels and film bubble pinhole blowouts.

Evidencia Customer Confirmation

Duración de la prueba: 10 commercial masterbatch batches
Fecha de la evidencia: 2024-02
Condiciones reales de entrada y salida: Downstream 15-micron LLDPE agricultural film blowing extrusion test.
Método de medición: Filter Pressure Value test according to EN 13900-5 using 615-mesh filter screen.

Zero Cross-Color Contamination Defects

The mirror-polished internal finish and flush-radius discharge door completely eliminated dead corners, achieving zero off-color contamination rejects across more than 400 production batches.